Monel Alloy K500 (NA18, N05500) offers an exceptionally high dimensional stability and, as with Monel Alloy 400, its low temperature mechanical properties are very good with no transition temperature, making the alloy suitable for many cryogenic applications. It does, however, have a greater tendency toward stress-corrosion cracking in some Alloy K500 Data Sheet - Maher Commonly referred to as Monel® K500 Alloy K500 is a nickel-copper alloy which combines the excellent corrosion resistance of Alloy 400 with higher strength and hardness obtained through the addition of aluminium and titanium to the nickel-copper base. It has excellent low temperature properties with tensile and yield strengths increasing
The effect of a cast alloy surface and internal defects versus wrought alloy soundness on service performance is illustrated by the Rolled Alloys case history, RA330-108. The application was a grid for suspending loads in a gantry furnace at a commercial heat treat shop. High Temperature Alloys:NITRONIC, INCONEL, HASTELLOY(Alloy 218) (UNS S21800) Fe 63, Cr 17, Mn 8, Ni 8.5, Si 4, N 0.13 High strength fully Austenitic alloy that resists galling and wear. Significantly lower cost to extend part life and lower maintenance. K Monel 500 - hamdenmetalK-500 Alloy has similar properties to Monel 400 Alloy, but has the added feature of Age Hardening to achieve a higher strength and hardness, This is due to the addition of aluminium and titanium. K-500 Alloys strength is maintained to temperatures as high as 1200 F, yet stays tough and ductile to temperatures down to -423 F. Along with staying non-magnetic down to -210 F.
Alloy K-500 is a nickel-copper alloy, which combines the excellent corrosion resistance of alloy 400 with the added advantages of greater strength and hardness. Alloy K-500 provides roughly three times the yield strength of alloy 400. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base and age hardening. K-500 Monel Material DatasheetThe corrosion resistance of alloy K-500 is substantially equivalent to that of Monel® 400 except that when in the age-hardened condition, nickel alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments. Monel® K-500 has been MONEL K-500 - Superalloys, High temperature alloy MONEL K-500 Application:Mainly used in the manufacture of aircraft engine working temperature in turbine blade and gas turbine blade below 750 DEG C; We are mainly engaged in the special steel, stainless steel, tool steel, alloy steel, high temperature alloys, heat-resistant steel rod, plate /sheet, strip/coil, steel wire,tube/pipe
MONEL K-500 Application:Mainly used in the manufacture of aircraft engine working temperature in turbine blade and gas turbine blade below 750 DEG C; We are mainly engaged in the special steel, stainless steel, tool steel, alloy steel, high temperature alloys, heat-resistant steel rod, plate /sheet, strip/coil, steel wire,tube/pipe Monel K-500 Nickel Alloy Alloys - Vincent MetalsChemical Data, Mechanical Properties and Specifications for Nickel Alloy K-500. Nickel K-500 combines the corrosion resistant properties of Nickel 400 with a greater tensile strength and superior hardness. It is often used in valve seals,pump shafts, cables, springs and fasteners. Monel Nickel McMaster-CarrFrom marine hardware to chemical-processing equipment, 400 nickel is widely used for its strength, weldability, and formability. Comparable to Monel, this nickel-copper alloy will stand up to highly corrosive environments, such as those involving salt water, sulfuric acid, and alkalies.. Certificates with a traceable lot number are available for these products.
About Monel K-500. Monel K-500 (Ni 63%) offers superior strength and hardness to Monel 400, otherwise both have same properties and corrosion resistance. In some conditions, N05500 offers great resistance to stress corrosion cracking. Better properties of this precipitation hardened metal are due to addition of Aluminum (Al) and ium (Ti) elements into its main chemistry. Monel® K-500 - Alloy Wire InternationalThis Nickel-Copper alloy is precipitation hardenable, due to the additions of Aluminium and ium. It combines the corrosion resistance of Monel 400 but gives the added advantage of extra strength and hardness (as a result of its age hardening ability). Monel® K-500 is also known as Nicorros Al. Nickel Alloy K-500, Monel® K-500 - Continental Steel Virtually nonmagnetic, even at quite low temperatures Exceptionally good dimensional stability Resistant to a sour-gas environment Excellent corrosion resistance together with increased strength and hardness of that of Alloy 400 Monel Alloy K-500 Special Metals popular Monel K-500 is a unique nickel-copper superalloy and offers many of the benefits of Monel 400, but with strength 
Mar 10, 2020 · There are multiple variations of Monel alloys, starting with Monel 400, which contains at least 63% nickel, between 29% and 34% copper, between 2% and 2.5% iron, and between 1.5% and 2% manganese. Monel 405 adds no more than 0.5% silicon, and Monel K-500 adds between 2.3% and 3.15% aluminum and between 0.35% and 0.85% titanium. VDM Alloy K-500 Nicorros AlJuly 2016 VDM® Alloy K-500 2 VDM® Alloy K-500 is a nickel-copper alloy that can be age-hardened due to additions of aluminum and titanium. It stands out for its corrosion resistance and high strength even at elevated temperatures. The alloy is non-magnetic. VDM® Alloy K-500 is available in cold or hot-formed condition or with subsequent heat treatment in solution-annealed or specialmetalsMONEL® alloy K-500 2 Figure 1. Effect of temperature on modulus of elasticity in tension of MONEL alloy K-500 (determined by dynamic method). 0 200 400 600 800 1000 Temperature, °F 26 23 24 25 3 Modulus of Elasticity, 10 ksi Table 3 - Thermal Properties of MONEL Alloy K-500
MONEL K500 is non-magnetic. MONEL K500 should be annealed when welded and the weldment then stress relieved before aging. High Performance Alloys, Inc. stocks Alloy K500 in a range of sizes including 3/8"-2-1/2" diameter cold drawn, annealed and aged, and